Kit contains 2 upper control arms with bushings that are approximately twice as stiff as current production bushings. Significantly improves  traction and handling when fitted to 1979-98 Mustang and 1993-98 Cobra V-8 models.

This kit enables owners of 1994-04 Mustangs to  upgrade to 2003 Cobra Mustang control arms. The kit  features 2 front lower control arm assemblies with 50%  stiffer front bushings and low-friction ball joints. This  control arm has a redesigned stamping to improve the turning  circle approximately 10% on 1994-98 Mustangs.

This kit enables owners of 1979-93 Mustang/Capri vehicles to upgrade them to 1996 levels with low-friction ball joints and improved inner  bushings. Dramatically improves impact harshness qualities of vehicle and is recommended when heavy-duty suspension components are added. NOTE: The ball joints in the kit have been  upgraded. They have an improved nylon bearing to further reduce impact harshness. (Since no measurable wear could be detected after 250,000 miles of  fleet testing, the wear detectors were eliminated.)  Kit includes LH and RH lower control arm assemblies.

Fits 2005-08 Mustangs Original equipment on 2007-08 SVT Mustang Increased strength ball joints Kit contains 1 RH and 1 LH lower control arm assembly NOTE: Some factory fasteners are one-time use. Please reference Ford service manual for reuse information and correct torque specifications.

Fits 2005-08 Mustang GT coupe Original equipment on convertible and 2007 SVT Mustang Increases chassis stiffness

Service replacement for the Mustang FR500C race car Higher durometer bushing enhances response of vehicle Will fit 2005-08 Mustang GT NOTE: Some factory fasteners are one-time use. Please reference Ford service manual for reuse information and correct torque specifications.

Fits 2005-08 Mustang GT rear suspension Service replacement for the Mustang FR500C race car Includes bushings and sleeve for upper rear control arm Increased durometer bushing for precise handling and control NOTE: Some factory fasteners are one-time use. Please reference Ford service manual for reuse information and correct torque specifications.

Fits 2005-08 Mustang Original equipment on 2007-08 SVT Mustang Increased bushing durometer and stiffness for higher horsepower applications NOTE: Some factory fasteners are one-time use. Please reference Ford service manual for reuse information and correct torque specifications.

This lower control arm relocates control arm mounting points to alter rear suspension geometry Traction under acceleration and braking is dramatically improved Dual control arm mounting points allow anti-squat and anti-dive adjustment for differing traction conditions Both ends of control arms are equipped with fluted polyurethane bushing

This lower control arm relocates control arm mounting points to alter rear suspension geometry Traction under acceleration and braking is dramatically improved Dual control arm mounting points allow anti-squat and anti-dive adjustment for differing traction conditions Both ends of control arms are equipped with fluted polyurethane bushing

This kit lowers all 1999-04 F-150  Lightning/F-150 Harley-Davidson models 30 mm (1.181") in all four corners. A simple front  coil/jounce bumper replacement and rear shackle replacement are the only items necessary  to enhance positive control. Both vehicles retain very good ride/launch  characteristics.

Lowers rear of vehicle 2" drop Contains all installation hardware 

This kit lowers 1997-03 F-150 standard cab,  SuperCab and SuperCrew with V-6 or V-8, approx. 2" front and 4" rear.  Includes new front coil springs, rear shackles and hangers and 4  specially tuned high-pressure gas shocks. Fits vehicles with V-6 or V-8  engines in standard cab (long and short bed) and SuperCab (short bed).  Improves appearance and handling with very acceptable ride  characteristics. NOTE: Not recommended for 1999-03 SVT F-150  Lightning. When used on 2001 SuperCab with 6' box and 5" dia.  driveshaft, the driveshaft may hit the crossmember on hard bumps. 2WD only.

Lowers truck 2" in the front, 5" in the back Includes front drop coil springs, rear flip kit, rear shocks, bump stops and hardware Fits all 2WD models Lowers vehicle roll center for better handling Does not fit 2004 F-150 Heritage

Engineered specifically for improved handling on the 2006-08 Fusion and  Milan Front wheel drive only Lowers car approximately 1.5" Gives a more aggressive looking stance as well  as increased handling dynamics May cause firmer ride than stock springs NOTE: Some factory fasteners are one-time use. Please reference Ford  service manual for reuse information and correct torque specifications.

SEE SPEC SHEET

These high-quality steel strut tower braces  stiffen 1979-93 Fox Mustangs and are designed to clear all production and many aftermarket  components and accessories. These braces come complete with all necessary fasteners and  instructions. Braces are “E” coated and painted  for corrosion resistance. These kits are extremely  competitively priced.

SEE SPEC SHEET

Fits 2005-08 Mustang GT without plastic engine  cover Parallel beam design for added rigidity Black powder coated Stainless steel Ford Racing emblem Does not fit V-6, supercharged GT or 2007-08 GT  with intake shroud NOTE: Some factory fasteners are one-time use.  Please reference Ford service manual for reuse information and correct torque  specifications.

SEE SPEC SHEET

This kit consists of specific rate front and  rear coil springs to improve the launch characteristics of your  1979-04 Mustang (except 1999-04 Cobra). An airbag is  also included for installation inside the right rear  coil spring. Fine tuning of the air pressure in the airbag  will help neutralize the axle torque reaction. Recommended for serious Drag Racers. Spring rates F-300/465, LH 180, RR 180/350.

SEE SPEC SHEET

These spring kits have been designed to lower  your Mustang and improve its handling. There will be some deterioration in ride  quality. NOTE: The height on some cars will vary.

SEE SPEC SHEET

SEE SPEC SHEET

SEE SPEC SHEET

SEE SPEC SHEET

Kit includes increased rate Mustang springs, anti-roll bars, shocks and struts tuned for use with this package Spring rates: front 600 lb.-in. and rear 250 lb.-in. Lowers 1994-98 vehicles 1" and 1999-04 vehicles .75" Will not fit 1999-04 Cobra Due to vehicle assembly tolerances, amount lowered may vary

SEE SPEC SHEET